I am using ADS 2015.1

I have downloaded Murata's library from http://www.murata.com/en-global/tool/library/keysight2

I placed capacitors and inductors from that library but when I hit to the simulation button it outputs this error:

+Error detected by hpeesofsim during netlist flattening. 'C1' is an instance of an undefined model 'GRM15'.+

+hpeesofsim (*) 430.shp Dec 7 2014+

+(64-bit windows built: 12/07/14 09:11:55)+

+Copyright Keysight Technologies, 1989-2015.+

+--------------------+

+Simulation terminated due to error.+

You can see the print screen attached. The library and schematics are located in the same working directory. Hpeesofsim does not show any error code when I select error then press the question mark button.

I disabled C1 then the program outputs error for C2, and so on. However, when I place a capacitor from the ADS' its own library, then it does not output any error.

*What could be the problem?*

Here is the netlist.log

+Options ResourceUsage=yes UseNutmegFormat=no EnableOptim=no TopDesignName="MyLibrary_lib:cell_2:schematic"+

+GRM15:C1 N__0 N__22 PartNumber=715+

+GRM15:C2 N__3 N__2 PartNumber=715+

+LQG15HS:L1 N__4 N__5 PartNumber=7+

+GRM15:C3 N__7 N__6 PartNumber=34+

+GRM15:C4 N__9 0 PartNumber=34+

+LQG15HS:L2 0 N__11 PartNumber=7+

+LQG15HS:L5 N__13 N__36 PartNumber=7+

+GRM15:C5 0 N__14 PartNumber=47+

+LQG15HS:L4 N__16 N__39 PartNumber=12+

+MLIN2:TL1 P1 N__0 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL2 P2 N__3 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL3 N__22 N__11 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL4 N__2 N__9 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL5 N__9 N__4 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL6 N__11 N__7 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL7 N__36 N__16 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MCURVE:Curve1 N__5 N__13 Subst="MSub1" W=25.0 mil Angle=90 Radius=30.0 mil+

+MCURVE:Curve2 N__13 N__6 Subst="MSub1" W=25.0 mil Angle=90 Radius=30.0 mil+

+MLIN2:TL8 N__36 N__14 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+model MSub1 MSUB H=10.0 mil Er=4.7 Mur=1 Cond=1.0E+50 Hu=3.9e+034 mil T=0 mil TanD=0 Rough=0 mil DielectricLossModel=1 FreqForEpsrTanD=1.0 GHz LowFreqForTanD=1.0 kHz HighFreqForTanD=1.0 THz RoughnessModel=2+

+S_Param:SP1 CalcS=yes CalcY=no CalcZ=no GroupDelayAperture=1e-4 FreqConversion=no FreqConversionPort=1 StatusLevel=2 CalcNoise=no SortNoise=0 BandwidthForNoise=1.0 Hz DevOpPtLevel=0 \+

+SweepVar="freq" SweepPlan="SP1_stim" OutputPlan="SP1_Output"+

+SweepPlan: SP1_stim Start=2.4 GHz Stop=2.5 GHz Step=0.5 GHz+

+OutputPlan:SP1_Output \+

+Type="Output" \+

+UseEquationNestLevel=yes \+

+EquationNestLevel=2 \+

+UseSavedEquationNestLevel=yes \+

+SavedEquationNestLevel=2+

+#load "python","LinearCollapse"+

+Component Module="LinearCollapse" Type="ModelExtractor" NetworkRepresentation=2+

+Port:Term2 N__39 0 Num=2 Z=50 Ohm Noise=yes+

I have downloaded Murata's library from http://www.murata.com/en-global/tool/library/keysight2

I placed capacitors and inductors from that library but when I hit to the simulation button it outputs this error:

+Error detected by hpeesofsim during netlist flattening. 'C1' is an instance of an undefined model 'GRM15'.+

+hpeesofsim (*) 430.shp Dec 7 2014+

+(64-bit windows built: 12/07/14 09:11:55)+

+Copyright Keysight Technologies, 1989-2015.+

+--------------------+

+Simulation terminated due to error.+

You can see the print screen attached. The library and schematics are located in the same working directory. Hpeesofsim does not show any error code when I select error then press the question mark button.

I disabled C1 then the program outputs error for C2, and so on. However, when I place a capacitor from the ADS' its own library, then it does not output any error.

*What could be the problem?*

Here is the netlist.log

+Options ResourceUsage=yes UseNutmegFormat=no EnableOptim=no TopDesignName="MyLibrary_lib:cell_2:schematic"+

+GRM15:C1 N__0 N__22 PartNumber=715+

+GRM15:C2 N__3 N__2 PartNumber=715+

+LQG15HS:L1 N__4 N__5 PartNumber=7+

+GRM15:C3 N__7 N__6 PartNumber=34+

+GRM15:C4 N__9 0 PartNumber=34+

+LQG15HS:L2 0 N__11 PartNumber=7+

+LQG15HS:L5 N__13 N__36 PartNumber=7+

+GRM15:C5 0 N__14 PartNumber=47+

+LQG15HS:L4 N__16 N__39 PartNumber=12+

+MLIN2:TL1 P1 N__0 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL2 P2 N__3 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL3 N__22 N__11 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL4 N__2 N__9 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL5 N__9 N__4 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL6 N__11 N__7 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MLIN2:TL7 N__36 N__16 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+MCURVE:Curve1 N__5 N__13 Subst="MSub1" W=25.0 mil Angle=90 Radius=30.0 mil+

+MCURVE:Curve2 N__13 N__6 Subst="MSub1" W=25.0 mil Angle=90 Radius=30.0 mil+

+MLIN2:TL8 N__36 N__14 Subst="MSub1" W=25.0 mil L=100.0 mil Wall1=1.0E+30 mil Wall2=1.0E+30 mil Mod=1+

+model MSub1 MSUB H=10.0 mil Er=4.7 Mur=1 Cond=1.0E+50 Hu=3.9e+034 mil T=0 mil TanD=0 Rough=0 mil DielectricLossModel=1 FreqForEpsrTanD=1.0 GHz LowFreqForTanD=1.0 kHz HighFreqForTanD=1.0 THz RoughnessModel=2+

+S_Param:SP1 CalcS=yes CalcY=no CalcZ=no GroupDelayAperture=1e-4 FreqConversion=no FreqConversionPort=1 StatusLevel=2 CalcNoise=no SortNoise=0 BandwidthForNoise=1.0 Hz DevOpPtLevel=0 \+

+SweepVar="freq" SweepPlan="SP1_stim" OutputPlan="SP1_Output"+

+SweepPlan: SP1_stim Start=2.4 GHz Stop=2.5 GHz Step=0.5 GHz+

+OutputPlan:SP1_Output \+

+Type="Output" \+

+UseEquationNestLevel=yes \+

+EquationNestLevel=2 \+

+UseSavedEquationNestLevel=yes \+

+SavedEquationNestLevel=2+

+#load "python","LinearCollapse"+

+Component Module="LinearCollapse" Type="ModelExtractor" NetworkRepresentation=2+

+Port:Term2 N__39 0 Num=2 Z=50 Ohm Noise=yes+

## Attachments

My case is a little odd! I made two sub circuits that each one includes MuRata elements. I put Netlist in each sub-circuit either. When I recall one sub-circuit, simulation will be done without any error. If one of this circuit is cascaded by itself, there is no problem either. But when I put two different sub-circuit in one simulation, this error (XX is an instance of an undefined model 'XX) appears. Each sub-circuit consists of bunch of different inductors and capacitors. By the Chance do you know what is the problem?

Thank you.