All,
I am using vee 6.01 and I can't get View->Variables (the globe) to show me
the declared vars in my program. It only shows the undeclared vars. Every
now and then however it does show the declared vars but if I close it and
open it again they're gone. How can I get it to work all the time?
Thanks,
Bill Drago
Test Engineer
L3 Communications - Narda Microwave East
435 Moreland Road
Hauppauge, NY 11788
William.Drago@L-3com.com
631-231-1700 Ext. 572
FAX 631-231-1480
---------------------------------------------------------------------
This is the "vrf" maillist, managed by Majordomo. To send messages to
this maillist, just email to "vrf@lvld.agilent.com". Subscriptions and
unsubscriptions are done through the address "vrf-request@lvld.agilent.com".
If you need details, just send a message containing the text "help"
to "vrf-request@lvld.agilent.com".
---------------------------------------------------------------------
I am using vee 6.01 and I can't get View->Variables (the globe) to show me
the declared vars in my program. It only shows the undeclared vars. Every
now and then however it does show the declared vars but if I close it and
open it again they're gone. How can I get it to work all the time?
Thanks,
Bill Drago
Test Engineer
L3 Communications - Narda Microwave East
435 Moreland Road
Hauppauge, NY 11788
William.Drago@L-3com.com
631-231-1700 Ext. 572
FAX 631-231-1480
---------------------------------------------------------------------
This is the "vrf" maillist, managed by Majordomo. To send messages to
this maillist, just email to "vrf@lvld.agilent.com". Subscriptions and
unsubscriptions are done through the address "vrf-request@lvld.agilent.com".
If you need details, just send a message containing the text "help"
to "vrf-request@lvld.agilent.com".
---------------------------------------------------------------------
I don't see this behavior. I always see the declared variables. In my
experience it's the undeclared ones that aren't created until they've been
set and so don't show up until then.
Regards,
Bill Ossmann
--
bill_ossmann@hsgmed.com
>-----Original Message-----
>From: Drago, William @ NARDAEAST [mailto:William.Drago@L-3com.com]
>Sent: Friday, March 29, 2002 8:44 AM
>To: 'Vee Reflector'
>Subject: vrf View Variables
>
>
>All,
>
>I am using vee 6.01 and I can't get View->Variables (the
>globe) to show me
>the declared vars in my program. It only shows the undeclared
>vars. Every
>now and then however it does show the declared vars but if I
>close it and
>open it again they're gone. How can I get it to work all the time?
>
>Thanks,
>Bill Drago
>Test Engineer
>L3 Communications - Narda Microwave East
>435 Moreland Road
>Hauppauge, NY 11788
>William.Drago@L-3com.com
>631-231-1700 Ext. 572
>FAX 631-231-1480
>---------------------------------------------------------------------
>This is the "vrf" maillist, managed by Majordomo. To send messages to
>this maillist, just email to "vrf@lvld.agilent.com". Subscriptions and
>unsubscriptions are done through the address
>"vrf-request@lvld.agilent.com".
>If you need details, just send a message containing the text "help"
>to "vrf-request@lvld.agilent.com".
>---------------------------------------------------------------------
>
---------------------------------------------------------------------
This is the "vrf" maillist, managed by Majordomo. To send messages to
this maillist, just email to "vrf@lvld.agilent.com". Subscriptions and
unsubscriptions are done through the address "vrf-request@lvld.agilent.com".
If you need details, just send a message containing the text "help"
to "vrf-request@lvld.agilent.com".
---------------------------------------------------------------------