Title		Author	Latest activity	Views
	pna-x opt28 noise figure channel conflicting settings	rok	May 23, 2017 9:29:16 AM by rok	19	Show 0 Likes0	Show 0 Bookmarks0	2 Replies2
	Network Analyzer GPIB->USB:  Newbie Questions	spidermonkey1187	May 23, 2017 6:45:46 AM by spidermonkey1187	52	Show 0 Likes0	Show 0 Bookmarks0	2 Replies2
	What is the physical meaning of X(s)and X(T) for different circumstances in the X-parameters	bowilzhang‘’	May 18, 2017 3:22:33 PM by bowilzhang‘’	57	Show 0 Likes0	Show 0 Bookmarks0	1 Replies1
	Some questions about Gating Effects in Time Domain Transforms?	mindhen	May 18, 2017 3:00:16 PM by mindhen	129	Show 0 Likes0	Show 0 Bookmarks0	3 Replies3
	Why I get this warning message "220, The GPS is currently unlocked"	Tamim	May 10, 2017 6:51:14 PM by Tamim	145	Show 0 Likes0	Show 0 Bookmarks0	4 Replies4
	S21 Phase Measurement problems between 8510C Test Sets	gr8sailor	April 27, 2017 1:21:09 PM by gr8sailor	112	Show 0 Likes0	Show 0 Bookmarks0	3 Replies3
	When using a PNA/PNA-X, how do I measure a pulsed RF signal output with a sampling oscilloscope?	CSGForumFAQ	April 24, 2017 10:51:34 AM by CSGForumFAQ	38	Show 1 Likes1	Show 0 Bookmarks0	2 Replies2
	Is there any way to run the N1500A material measurement software without a VNA?	drkirkby	April 20, 2017 5:26:13 PM by drkirkby	11	Show 0 Likes0	Show 0 Bookmarks0	0 Replies0
	Can a CalPod system be used with the N1500A software?	CSGForumFAQ	April 20, 2017 7:18:51 AM by CSGForumFAQ	45	Show 3 Likes3	Show 0 Bookmarks0	2 Replies2
	Does the Maury Microwave MT7553B03 50 GHz Noise Receiver Module lower the effective noise figure of the N5245A beyond that of option 029?	CSGForumFAQ	April 19, 2017 5:25:14 PM by CSGForumFAQ	31	Show 0 Likes0	Show 0 Bookmarks0	1 Replies1
	Does the noise figure application on the PNA-X (option 029) provide a full noise-parameter system (tuners and software)?	CSGForumFAQ	April 19, 2017 5:25:14 PM by CSGForumFAQ	42	Show 0 Likes0	Show 0 Bookmarks0	1 Replies1
	Can Keysight PXIe VNAs be used with Non-Keysight PXI Chassis?	CSGForumFAQ	April 19, 2017 5:25:10 PM by CSGForumFAQ	18	Show 0 Likes0	Show 0 Bookmarks0	1 Replies1
	NF calibration: Power sensor vs Noise Source	YP	April 16, 2017 7:38:12 PM by YP	118	Show 0 Likes0	Show 0 Bookmarks0	4 Replies4
	For attenuators specified by the OEM to operate DC-xGHz but are only verified with a VNA (50MHz-xGHz), has the attenuator really been verified to OEM specs.?	jchristian	March 22, 2017 3:23:01 PM by jchristian	36	Show 0 Likes0	Show 0 Bookmarks0	1 Replies1
	Does N5242A PNA-X support probing for power measurement?	andydang	March 22, 2017 3:19:34 PM by andydang	80	Show 0 Likes0	Show 0 Bookmarks0	1 Replies1
	PNA-X SA Mode two tone measurements	Neilfenstein	March 22, 2017 3:14:45 PM by Neilfenstein	177	Show 0 Likes0	Show 0 Bookmarks0	3 Replies3
	Specification of ADC in N5244 with 118	zubair_rafiq	March 22, 2017 3:12:04 PM by zubair_rafiq	122	Show 0 Likes0	Show 0 Bookmarks0	3 Replies3
	how to get the DC loss term in the port extension setup？	mindhen	March 22, 2017 3:07:38 PM by mindhen	82	Show 1 Likes1	Show 0 Bookmarks0	3 Replies3
	Averaging S2P files	RickM	March 22, 2017 8:35:59 AM by RickM	74	Show 0 Likes0	Show 0 Bookmarks0	2 Replies2
	use IFFT (matlab) for transforming frequency domain to time domain	meta5718	March 20, 2017 2:08:18 PM by meta5718	5598	Show 1 Likes1	Show 0 Bookmarks0	11 Replies11